The first coat is simply a base and will be skimmed very tightly, so little remains. The second coat is what will fill in the joints and hide them. The third coat will give the wall a uniform and expert look.
This article will go over the following: The most common causes of air bubble formation in your drywall mud.
Solutions for fixing air bubbles in your drywall mud to create the desired result every time. Provide a few basic compound application tips. Suggestions for where you can purchase quality mud that will get the job done right. Note that we are using the terms mud and joint compound interchangeably throughout this article.
Compounding Over Painted Walls While you usually apply mud to new and unpainted drywall, there are situations where you need to use joint compound for patching over holes or cracks in painted drywall.
Not Enough Compound Was Left Underneath Your Tape Another frequent cause of drywall mud bubbling, specifically under the tape, is that beginners press too much mud out from under their tape with their knife, which does not only cause the mud to bubble but will also leave your tape with a poor and unreliable adhesion that is bound to lift and separate sooner or later.
How To Fix Air Bubbles in Drywall Mud The best way to fix air bubbles in drywall mud is by adjusting how many coats you apply to the wall and how you apply them. Follow those steps for each coat in order to fix bubbles in drywall mud: Apply the first coat of mud, then skim it very tightly with your knife at an angle of 45 degrees.
The first layer aims to form a base and fill whatever joints, cracks, or holes. Immediately after applying this first coat, scrape it very tightly until little remains. Apply the second coat. The purpose of this second coat is to fill in and cover your joints, mask and make them invisible, and to give your wall a nice smooth and professional look. Skim over the surface again with your knife, but with much less pressure. You now know that the common reason for air bubbles appearing under drywall tape is poor installation, you can find comfort in knowing that there are ways to fix this before you finish the joint.
SFGate Home Guides gives a walkthrough to this process. The first thing to do is to make a cut just above and below the bubbled section. Use a utility knife and remove the tape between the cuts. You can remove the entire tape if the blisters are present all throughout. Second, mix the drywall compound to a creamy consistency. Apply a layer of the compound to the joint or area below the removed tape.
Be sure this layer is a bit wider than the width of the tape. Next, tear a piece of drywall tape to fit the required length. Center the tape over the area and then place it on the drywall compound. Once that is done, hold the top edge of the tape and pull the drywall knife down the tape.
Press evenly, making sure to embed the tape into the compound, removing any air bubbles. Joint compound does shrink and is intended to be applied over large areas in multiple coats. And your initial job looks reasonable. Let it dry thoroughly; maybe aim a fan at it if you want to speed it along.
Sand it down and do a second and then third coat, sanding between. Stir the compound thoroughly before you put it on; that will help. Add a comment. Active Oldest Votes. That said, I have a few ideas: Add a little bit of water. The further along in the finishing process, the thinner the compound should be. Mix well, even if you add no water. It's hard to tell from the pictures, but it looks like your application could use fine tuning.
Apply the mud to the wall as you have done. Remove mud from the knife and, putting pressure on the left side of the knife, go back over application. Do the same for the right side. With light pressure in the center, go over again. This will help to better feather out our edges. Improve this answer. Edwin Edwin 4, 2 2 gold badges 15 15 silver badges 23 23 bronze badges.
Edwin 4, 2 2 gold badges 15 15 silver badges 23 23 bronze badges. I found an old potato masher works well for mixing the drywall compound. The bubbles are usually from not mixing the mud well enough or not applying it with enough pressure. It is not unusual to see lots of small bubbles on the first coat. Here's a little trick for your third or final coats of mud.
Mix a small amount of water and Ivory dish soap into your mud and mix well. Also, why does drywall mud bubble on paint? Any air coming from the drywall compound fissures will just bubble through the wet film.
After a few hours the cracks in the mud also dry out. The water will eventually evaporate from the fissures and by the time of the next paint job they will be ready to produce blisters all over again. Uneven drying — uneven drying, or a lack of 'curing' time for your plaster or stucco wall can also contribute to nasty air bubbles. The trapped moisture inside will cause the paint to blister due to the presence of water that attempts to come out as the plaster and paint as they both drying. Apply three or more coats of very thin compound rather than one or two heavier coats.
Yes, it takes time for the compound to dry, but don't try to rush the drywall taping process along by applying fewer, thicker coats. What causes drywall tape to wrinkle?
0コメント